194 lines
6.7 KiB
Groff
194 lines
6.7 KiB
Groff
7.2.4
|
|
|
|
|
|
|
|
R1#conf t
|
|
Enter configuration commands, one per line. End with CNTL/Z.
|
|
R1(config)#inf fa0/0
|
|
^
|
|
% Invalid input detected at '^' marker.
|
|
|
|
R1(config)#interface fa0/0
|
|
R1(config-if)#no shutdown
|
|
R1(config-if)#
|
|
*Mar 1 00:05:38.967: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
|
|
*Mar 1 00:05:39.967: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
|
|
R1(config-if)#
|
|
R1#interface fa0/0
|
|
*Mar 1 00:05:44.943: %SYS-5-CONFIG_I: Configured from console by console
|
|
R1#interface fa0/0
|
|
R1#conf t
|
|
Enter configuration commands, one per line. End with CNTL/Z.
|
|
R1(config)#interface fa0/0
|
|
R1(config-if)#no shutdown
|
|
R1(config-if)#interface fa0/0.10
|
|
R1(config-subif)#ip address 192.168.100.1 255.255.255.0
|
|
|
|
% Configuring IP routing on a LAN subinterface is only allowed if that
|
|
subinterface is already configured as part of an IEEE 802.10, IEEE 802.1Q,
|
|
or ISL vLAN.
|
|
|
|
R1(config-subif)#enxa
|
|
R1(config-subif)#enca
|
|
R1(config-subif)#encapsulation d
|
|
R1(config-subif)#encapsulation dot1Q 10
|
|
R1(config-subif)#ip address 192.168.100.1 255.255.255.0
|
|
R1(config-subif)#
|
|
*Mar 1 00:07:20.543: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
|
|
R1(config-subif)#exi
|
|
R1(config)#ip dhcp pool LAN-U
|
|
R1(config)#ip dhcp pool LAN-U
|
|
R1(config)#ip dhcp pool LAN-USERS
|
|
R1(dhcp-config)#network 192.168.100.0 255.255.255.0
|
|
R1(dhcp-config)#default-router 192.168.100.1
|
|
R1(dhcp-config)#exi
|
|
R1(config)#ip dhcp exc
|
|
R1(config)#ip dhcp excluded-address 192.168.100.1 192.168.100.10
|
|
R1(config)#ip access-list extended USERS
|
|
R1(config-ext-nacl)#
|
|
R1#conf t
|
|
*Mar 1 00:10:09.859: %SYS-5-CONFIG_I: Configured from console by console
|
|
R1#conf t
|
|
Enter configuration commands, one per line. End with CNTL/Z.
|
|
R1(config)#ip nat inside source list USERS interface fa
|
|
R1(config)#ip nat inside source list USERS interface fastEthernet
|
|
R1(config)#ip nat inside source list USERS interface fastEthernet0
|
|
R1(config)#ip nat inside source list USERS interface fastEthernet0
|
|
R1(config)#ip nat inside source list USERS interface fastEthernet0
|
|
R1(config)#ip nat inside source list USERS interface
|
|
R1(config)#ip nat inside source list USERS interface
|
|
R1(config)#ip nat inside source list USERS interface
|
|
R1(config)#ip nat inside source list USERS interface Fa
|
|
R1(config)#$de source list USERS interface FastEthernet 0/1 overload
|
|
R1(config)#ip access-list extended USERS
|
|
*Mar 1 00:10:52.087: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, changed state to up
|
|
R1(config)#ip access-list extended USERS
|
|
R1(config-ext-nacl)#permit ip 192.168.100.0 0.0.0.255 any
|
|
R1(config-ext-nacl)#ex
|
|
R1(config)#ip dhcp excluded-address 192.168.100.1 192.168.100.10
|
|
R1#
|
|
*Mar 1 00:11:41.515: %SYS-5-CONFIG_I: Configured from console by console
|
|
R1#conf t
|
|
Enter configuration commands, one per line. End with CNTL/Z.
|
|
R1(config)#ip nat outside
|
|
R1#conf t
|
|
*Mar 1 00:11:58.307: %SYS-5-CONFIG_I: Configured from console by console
|
|
R1#conf t
|
|
Enter configuration commands, one per line. End with CNTL/Z.
|
|
R1(config)#int f
|
|
R1(config)#int fastEthernet
|
|
R1(config)#int fastEthernet
|
|
R1(config)#int fastEthernet0/1
|
|
R1(config-if)#
|
|
R1#conf t
|
|
Enter configuration commands, one per line. End with CNTL/Z.
|
|
R1(config)#int fastEthernet0/1
|
|
*Mar 1 00:12:12.783: %SYS-5-CONFIG_I: Configured from console by console
|
|
R1(config)#int fastEthernet 0/1
|
|
R1(config-if)#ip nat outside
|
|
R1(config-if)#exit
|
|
R1(config)#int fastEthernet 0/0.10
|
|
R1(config-subif)#ip nat inside
|
|
R1(config-subif)#exit
|
|
R1(config)#interface lo
|
|
% Incomplete command.
|
|
|
|
R1(config)#interface loopback 1
|
|
R1(config-if)#
|
|
*Mar 1 00:13:25.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to up
|
|
R1(config-if)#ip nat inside
|
|
R1(config-if)#ip route 0.0.0.0 0.0.0.0 172.16.0.2
|
|
R1(config)#ping 1.1.1.1 192.168.6.1
|
|
^
|
|
% Invalid input detected at '^' marker.
|
|
|
|
R1(config)#ping 1.1.1.1 192.168.6.1
|
|
R1#
|
|
*Mar 1 00:14:37.683: %SYS-5-CONFIG_I: Configured from console by console
|
|
R1#
|
|
R1#ping 1.1.1.1 192.168.6.1
|
|
^
|
|
% Invalid input detected at '^' marker.
|
|
|
|
R1#ping 1.1.1.1 source 192.168.6.1
|
|
|
|
% Invalid source address- IP address not on any of our up interfaces
|
|
R1#ping 1.1.1.1 source 192.168.100.1
|
|
|
|
Type escape sequence to abort.
|
|
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
|
|
Packet sent with a source address of 192.168.100.1
|
|
.....
|
|
Success rate is 0 percent (0/5)
|
|
R1#ping 8.8.8.8 source 192.168.100.1
|
|
|
|
Type escape sequence to abort.
|
|
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
|
|
Packet sent with a source address of 192.168.100.1
|
|
.....
|
|
Success rate is 0 percent (0/5)
|
|
R1#ping 8.8.8.8 source 192.168.100.10
|
|
|
|
% Invalid source address- IP address not on any of our up interfaces
|
|
R1#ping 8.8.8.8 source 192.168.100.0
|
|
|
|
% Invalid source address- IP address not on any of our up interfaces
|
|
R1#ping 8.8.8.8 source 192.168.100.1
|
|
|
|
Type escape sequence to abort.
|
|
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
|
|
Packet sent with a source address of 192.168.100.1
|
|
.....
|
|
Success rate is 0 percent (0/5)
|
|
R1#ip a
|
|
^
|
|
% Invalid input detected at '^' marker.
|
|
|
|
R1#ip address
|
|
^
|
|
% Invalid input detected at '^' marker.
|
|
|
|
R1#ping 8.8.8.8 source 192.168.100.1
|
|
R1#
|
|
R1#
|
|
R1#
|
|
R1#help
|
|
Help may be requested at any point in a command by entering
|
|
a question mark '?'. If nothing matches, the help list will
|
|
be empty and you must backup until entering a '?' shows the
|
|
available options.
|
|
Two styles of help are provided:
|
|
1. Full help is available when you are ready to enter a
|
|
command argument (e.g. 'show ?') and describes each possible
|
|
argument.
|
|
2. Partial help is provided when an abbreviated argument is entered
|
|
and you want to know what arguments match the input
|
|
(e.g. 'show pr?'.)
|
|
|
|
R1#?
|
|
Exec commands:
|
|
access-enable Create a temporary Access-List entry
|
|
access-profile Apply user-profile to interface
|
|
access-template Create a temporary Access-List entry
|
|
alps ALPS exec commands
|
|
archive manage archive files
|
|
audio-prompt load ivr prompt
|
|
auto Exec level Automation
|
|
beep Blocks Extensible Exchange Protocol commands
|
|
bfe For manual emergency modes setting
|
|
call Voice call
|
|
ccm-manager Call Manager Application exec commands
|
|
cd Change current directory
|
|
clear Reset functions
|
|
clock Manage the system clock
|
|
cns CNS agents
|
|
configure Enter configuration mode
|
|
connect Open a terminal connection
|
|
copy Copy from one file to another
|
|
credential load the credential info from file system
|
|
crypto Encryption related commands.
|
|
ct-isdn Run an ISDN component test command
|
|
|
|
R1#
|
|
R1#$face FastEthernet0/0, changed state to up*Mar 1 00:05:39.967: %LINEPROT
|